Marsupilami

Here's mine with a demo : https://www.atarinside.com/blog/index.php/atarinside-items/sprachbox-voice-box/

Thanks. Yes, i know this video but it doesn't help since i don't have the same problem.

I can't edit the first post anymore so here a video of the problem :

Hello, I bought an INTV piano and it doesn't work. It makes one continuous sound and none of the keys work. Is there a diagram of the piano board? I used the ROM synth.bin (https://forums.atariage.com/topic/193981-reading-the-ecs-keyboards/) to test and here's the result: I tried to remove the first 20cm of the conductive foam but problem remains. There is a 9 key space between each stucked keys. If i use the normal keyboard (the one for the Basic) the "#1" in the picture is the "0 (Zero)" key, the "#2" is the 8 key, the "#3" is the 6 key and so on. From what I found in the other post above there is something wrong with column 5 of the table : 00FE | $00FF bits bits | 0 1 2 3 4 5 6 7 ------+----------------------------------------------------------------- 0 | left, period, scolon, p, esc, 0, enter, [n/a] 1 | comma, m, k, i, 9, 8, o, l 2 | n, b, h, y, 7, 6, u, j 3 | v, c, f, r, 5, 4, t, g 4 | x, z, s, w, 3, 2, e, d 5 | space, down, up, q, 1, right, ctl, a 6 | [n/a], [n/a], [n/a], [n/a], [n/a], [n/a], [n/a], shift So I think of a failing HCF4050BE ? I ordered one (luckily they are easy to find). What do you think about it ? What could be the cause of the failure? Thanks.

Thanks for the information, my Side3.0 works fine now with my 1200xl and the 74F08PC 👍. I found a modification on the old component, I don't know what it does... Could someone tell me if I should reproduce this on the 74F08? Thanks

@Stephen, the problem is solved : The pcb was askew / incorrectly positioned in the shell.

I only have 2x3.0 Side3. So maybe the 3.1 is bigger ? But on your 3rd picture where the sticker "3.1" is visible, the card is not centered in the center of the shell (the hole in the center of the card). I had to push it a little so that it fits in the shell (you should hear a "click" once the hole is in place around the "pillar" for the screw). And then you may be able to close the shell and test.

I've just shared a new shell that will fit in another post but just in case : https://www.atarinside.com/blog/index.php/new-shell-for-the-side3-cartridge-and-your-1200xl/

The Side3 is awesome but the provided shell does not fit into the 1200xl cartidge port. So i’ve adapted the existing 3D model so that it will fit. You can download the STL here : https://www.atarinside.com/blog/index.php/new-shell-for-the-side3-cartridge-and-your-1200xl/

Not really. I've noticed that if you remove the shell, you can insert the Side3 PCB into the 1200xl. I have created a special shell in 3D (to print) that works. I will post this on my site and put a link here.

Thanks @Beeblebrox No, there is a UAV, a TFHH 512k Ram Expansion, a 800xl mmu, and the Basic RevC+800xl OS ROM REV2 ...so internally it's more a 800xl now. And TFHH also removed the heatsink, installed a linear voltage regulator (four classic 1N diodes) and a new 6800uf Cap. I have 2 other stock 1200Xl on which i haven't tried the Side3 yet. Just to be sure, can you tell me if it's the one in yellow above that i will need to change ? Thanks

Hi, I have the same problem with my 1200xl and my 2 Side3. Any other cartridge will work including the good old Atarimax myide+flash but the Side3. Can you tell me which 74F08 to buy? On ebay there are 74F08N and 74F08PC. It may be the same thing but it is beyond my knowledge And B.T.W., are we talking about the one with the yellow square in the picture below ? Thanks a lot

Hi, Is this project still in progress? There has been no news for a long time. Thanks

Awesome ! Thank you so much @amarok 👍🙌 21 frames will be too much for the memory remaining on the Arduino but if i remove some other animations (like frogger, choplifter, tutankham) and if i use only 10 frames of your Gif (one out of two), it should fit. Thanks again ! 😎

Very Nice (and lucky you) ! I must try to build one ! Again with an Esp32 with the WLED firmware and some Led...

Thanks Yes it will be me a cool frame on my desk and a Christmas decoration Basically it's just 4 8x8 led matrix like this : https://www.amazon.fr/gp/product/B07Z7RGHNF/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 (40€/$) Plus an arduino or an esp32 (around 5 or 10€/$) So the budget is roughly 50$ maximum...and time. It's still a work in progress but it's pretty good

Yes, I know, I don't want to have something 100% accurate. I also thought about getting the TOS 1.04 logo but I couldn't get all the frames out.

Thanks for the link 👍, i'll try with this one.

Hello, I am working on a personal project based on LEDs arrays and Arduino. I'm looking for the Atari logo with colors that cycle over a dozen frames in 16x16 pixel format. A bit like this one but in better quality and without the word Atari: I tried to reduce this one but the result is ugly 😢 Do you have this? Or a Game/Basic program for Altirra that would allow me to output the frames to a few .png? Thanks 🙌

Thanks ! What is the difference between the 2 files please ?

Hello, thank you for the program. I have a problem to enter the path of XFD files with a windows and a French keyboard : It's impossible to send the "\" key. Normally it is with "Alt Gr "+"8". I also tried with "Alt Gr "+"92" but same problem. Any idea ? Thanks

Nice, i'd like to order one please :) Thanks.

Awesome ! ? Thanks a lot Still waiting for the cheat codes to be enabled...or revealed... ?

Hi, here's mine (NTSC)

You've done it! Congratulations! ? ? And thank you so much, I can imagine there were tears and blood to finish it! Just one question: What are the cheat codes? How is it possible to choose the starting level? ?