santosp Posted January 24, 2019 Share Posted January 24, 2019 (edited) I believe they are 1uf. Digikey sells 500 for $35. Actually have marked as 104 -> 10 + 0000 zeros -> 100.000 Picofarad -> 100 Nanofarad -> 0.1 Microfarad This is the standard value of "decoupling capacitors" for the ic's. Edited January 24, 2019 by santosp 1 Quote Link to comment Share on other sites More sharing options...
Punisher5.0 Posted January 26, 2019 Share Posted January 26, 2019 Alright guys lets stay on topic and refrain from bickering please 1 Quote Link to comment Share on other sites More sharing options...
namrood Posted September 3, 2019 Share Posted September 3, 2019 (edited) Hi all. I know this is an old post but I need a bit of help. I'm new to all this but I have had a GQ-4X programmer for sometime but never used it. I would like to try and repair a few of the games I have bought as some of the gold connectors have come of the cart. My idea is to unsolder the 'HI' & 'Lo' eproms and solder them back on to a donor board. But if I was to replace the eeprom Memory and/or 93C86 or 93C66 ram eeprom (as mentioned in the tutorial) what information do I need to write to those chips? Thanks Edited September 3, 2019 by namrood Quote Link to comment Share on other sites More sharing options...
neo_rg Posted September 3, 2019 Share Posted September 3, 2019 Those are memory save eeproms. You don't need to do anything to them, just desolder/resolder them. 1 Quote Link to comment Share on other sites More sharing options...
Clint Thompson Posted September 8, 2019 Share Posted September 8, 2019 I went through the entire thread but didn't see it mentioned other than not requiring to be closed but what exactly are the C2/C3 spots for? Some carts are closed and others are open and while it doesn't seem to matter in the end, would still like to know why or what the actual purpose of these are for. Quote Link to comment Share on other sites More sharing options...
Zerosquare Posted September 8, 2019 Share Posted September 8, 2019 They're extra decoupling capacitors to stabilize the power delivery to the chips. I guess Atari found out that it worked fine without them and saved a few cents by removing them. 1 1 Quote Link to comment Share on other sites More sharing options...
+cubanismo Posted July 31, 2020 Share Posted July 31, 2020 (edited) Just wanted to post a helpful note on this thread about the EEPROMs (The save-game flash, not the big chips with the read-only game data). There's lot's of info out there noting you should use the 93c46/93c66/93c86 chips as appropriate for the game you're building, but it is rarely noted (Found some references in the Rebooteroids public beta thread and a few other buried references) that there are two (Well, three. I'll get to this.) variants of all these chips: one with 8-bit and the other with 16-bit data organization. Jaguar expects the flash organized as 16-bit words, as noted here: https://www.mulle-kybernetik.com/jagdox/cartridge.html. Look at the datasheet before you buy, and be sure you're getting the right memory organization variant. You can also get these chips in a variant that can support either mode depending on the value of an "Org" pin on the chip (Pin 6 on the 8-pin DIP Jag carts use), and this pin is floating on the Jaguar cartridge PCBs, so if you have one of these, just short pin 6 to pin 8 (VCC) to select 16-bit mode (Be sure that's the right value for your particular chip of course). On the chips I bought, pin 7 was also a write-protect bit, and had to be shorted to VCC as well to enable writes at all, as this pin also floats on the Jaguar cartridge PCBs. I just laid a bit of the capacitor leads that I snipped off after soldering those across all 3 of these pins and soldered it down to accomplish this. As usual, one of @Matthias's tools is a huge help here: If you have the right EEPROM and have it configured correctly, his EEPROM browser should auto-detect it and be able to manipulate the data on it. If you made a mistake somewhere, it won't report that the chip type was "detected", and/or you won't be able to manipulate the data. Of course, this only works if you have a BJL'd Jaguar, which everyone but me and a few other crazies thinks is heresy these days ? Not a huge deal, but gave me quite a scare initially when I went to build some of those unpopulated fancy black PCBs from eBay after only recycling scrap cartridges from B&C in prior builds, which already had EEPROMs and capacitors on them, and wasn't getting any data saved! Edited July 31, 2020 by cubanismo 5 Quote Link to comment Share on other sites More sharing options...
Clint Thompson Posted August 3, 2020 Share Posted August 3, 2020 On 7/31/2020 at 4:43 AM, cubanismo said: Not a huge deal, but gave me quite a scare initially when I went to build some of those unpopulated fancy black PCBs from eBay after only recycling scrap cartridges from B&C in prior builds, which already had EEPROMs and capacitors on them, and wasn't getting any data saved! Just as a heads up, I have about 100 new black PCBs that I'll sell in lots of 5 for $20 shipped within the U.S. if there is any interest (the boards listed on eBay are not mine): 1 Quote Link to comment Share on other sites More sharing options...
CLS Posted February 10, 2021 Share Posted February 10, 2021 Is it possible to just program/burn a game on one 4 mb rom chip ? Quote Link to comment Share on other sites More sharing options...
Zerosquare Posted February 10, 2021 Share Posted February 10, 2021 In theory yes, but you'd have to design a new PCB. It would also make cartridge access slower, which may cause problems with some games. I don't think anyone has ever tested it. 1 Quote Link to comment Share on other sites More sharing options...
CLS Posted February 10, 2021 Share Posted February 10, 2021 (edited) is it possible to use 2 M27C322 eproms 42 pin- 4mb in place of 27C800 eprom (42 pin - 1 MB) 27C160 eprom (42 pin - 2 MB) Edited February 10, 2021 by CLS Quote Link to comment Share on other sites More sharing options...
CLS Posted February 10, 2021 Share Posted February 10, 2021 52 minutes ago, Zerosquare said: In theory yes, but you'd have to design a new PCB. It would also make cartridge access slower, which may cause problems with some games. I don't think anyone has ever tested it. is it possible to use 2 4mb eproms M27C322 i have a bunch of these on hand? I ordered the correct ones but they will not arrive for a while still. Quote Link to comment Share on other sites More sharing options...
Zerosquare Posted February 10, 2021 Share Posted February 10, 2021 (edited) M27C322 EPROM chips appear to have the same pinout as the original ones, except pin #32 is A20 instead of /BYTE. So this should work, but you need to program the original ROM file contents into both halves of the EPROM. The programming software may have an option to do that, otherwise you can use a command prompt to create a suitable ROM file for your 4 Mb EPROMs: copy /b input_file.rom+input_file.rom output_file.rom Edited February 10, 2021 by Zerosquare 2 Quote Link to comment Share on other sites More sharing options...
CLS Posted February 11, 2021 Share Posted February 11, 2021 2 hours ago, Zerosquare said: M27C322 EPROM chips appear to have the same pinout as the original ones, except pin #32 is A20 instead of /BYTE. So this should work, but you need to program the original ROM file contents into both halves of the EPROM. The programming software may have an option to do that, otherwise you can use a command prompt to create a suitable ROM file for your 4 Mb EPROMs: copy /b input_file.rom+input_file.rom output_file.rom Thank You for this info. can you elaborate more on when you refer to " original rom file contents " ? . Currently what I have done is used romsplit to split the avp.rom in 2 parts a HI and LO rom 2048kb each. What else needs done before writing files to eprom. Current name of files is AVP.HI & AVP.LO. Thanks in advance. Quote Link to comment Share on other sites More sharing options...
Zerosquare Posted February 11, 2021 Share Posted February 11, 2021 You need to type this in a command line: copy /b AVP.HI+AVP.HI AVP_HI.BIN copy /b AVP.LO+AVP.LO AVP_LO.BIN You'll get two 4096 kB files, AVP_HI.BIN and AVP_LO.BIN. Those are the files you should use to program your two M27C322 EPROMs. 1 Quote Link to comment Share on other sites More sharing options...
CLS Posted February 11, 2021 Share Posted February 11, 2021 1 hour ago, Zerosquare said: You need to type this in a command line: copy /b AVP.HI+AVP.HI AVP_HI.BIN copy /b AVP.LO+AVP.LO AVP_LO.BIN You'll get two 4096 kB files, AVP_HI.BIN and AVP_LO.BIN. Those are the files you should use to program your two M27C322 EPROMs. Thank you that worked great for me. Quote Link to comment Share on other sites More sharing options...
CLS Posted February 12, 2021 Share Posted February 12, 2021 (edited) On 2/10/2021 at 9:01 PM, Zerosquare said: You need to type this in a command line: copy /b AVP.HI+AVP.HI AVP_HI.BIN copy /b AVP.LO+AVP.LO AVP_LO.BIN You'll get two 4096 kB files, AVP_HI.BIN and AVP_LO.BIN. Those are the files you should use to program your two M27C322 EPROMs. Hello. This method is working good for all 4mb jaguar games Thank You. But did not work for the 2mb games. After I apply the copy command I am left with a LO and HI rom 2048 kb in size each. I tried copying these files x 3 to make them 4mb which made them the correct size. But they failed during the write/programming step. Any Ideas what to try? Thanks in advance Edited February 12, 2021 by CLS Quote Link to comment Share on other sites More sharing options...
Zerosquare Posted February 12, 2021 Share Posted February 12, 2021 Try erasing and programming again. If the files are the correct size, there's no reason why it shouldn't work. 1 Quote Link to comment Share on other sites More sharing options...
CLS Posted February 14, 2021 Share Posted February 14, 2021 (edited) On 2/12/2021 at 9:29 AM, Zerosquare said: Try erasing and programming again. If the files are the correct size, there's no reason why it shouldn't work. got it to work thanks. On a different subject do you think a sega genesis game pcb that contains two 2mb rom chips could be swapped and programmed with m27c322 eproms by using the same routine as the Jaguar games? Creating hi and lo then matching the the correct eprom size? I Have not really seen much documentation on sega games with 2 rom chips. Edited February 14, 2021 by CLS Quote Link to comment Share on other sites More sharing options...
Zerosquare Posted February 14, 2021 Share Posted February 14, 2021 It depends on the ROM chips that are used in Genesis cartridges. If they're the same as those in Jaguar cartridges, it should work as well. 1 Quote Link to comment Share on other sites More sharing options...
rayik Posted February 16, 2021 Author Share Posted February 16, 2021 (edited) On 2/10/2021 at 11:31 AM, CLS said: is it possible to use 2 4mb eproms M27C322 i have a bunch of these on hand? I ordered the correct ones but they will not arrive for a while still. Yes, it works. You can use chips bigger than the files you are burning. I've burned 2mb games onto two 2mb chips. The burner I use starts the burn at address 0 and goes up from there. You just do not want to do the opposite. Burning 4mb games onto two 1mb chips results in a not working game. *** EDIT Sorry, I did not comprehend what you were asking. I'm not sure if those 4mb chips are pin compatible with the 1mb and 2mb chips. Zerosquare does know and helped you. Looks like you burned successfully by filling the entire chip. *** END EDIT Edited February 16, 2021 by rayik 1 Quote Link to comment Share on other sites More sharing options...
Gedalya Posted January 24, 2022 Share Posted January 24, 2022 I see a program called romsplit referenced however I do not see where to download it; would someone point me to it please? I have found some other threads and sites even that make reference but no where to download it. Quote Link to comment Share on other sites More sharing options...
+MacRorie Posted January 24, 2022 Share Posted January 24, 2022 17 minutes ago, Gedalya said: I see a program called romsplit referenced however I do not see where to download it; would someone point me to it please? I have found some other threads and sites even that make reference but no where to download it. If someone thinks this file shouldn't be here, please kindly let me know and I will delete it. However, this has ROMSPLIT, docs for it, and other useful files. I seem to have gotten it from a Jag Dev kit CD. UTILPC.ZIP 1 Quote Link to comment Share on other sites More sharing options...
Gedalya Posted January 24, 2022 Share Posted January 24, 2022 11 minutes ago, MacRorie said: If someone thinks this file shouldn't be here, please kindly let me know and I will delete it. However, this has ROMSPLIT, docs for it, and other useful files. I seem to have gotten it from a Jag Dev kit CD. UTILPC.ZIP 433.7 kB · 0 downloads Thank you!!! Quote Link to comment Share on other sites More sharing options...
Gedalya Posted January 29, 2022 Share Posted January 29, 2022 @Dragonstomper, this is a wonderful guide and very helpful for someone like myself. I do have a recommendation; quoting from the guide: Quote 27C800 eprom (42 pin - 1 MB) 27C160 eprom (42 pin - 2 MB) (can uses these as substitute for 27C800) 42 pin DIC IP sockets (if you want to socket eeproms rather than solder directly to PCB) I believe the last reference should read "DIP IC" and not "DIC IP"; also I think the same line should be edited to include the information "2.54 pitch" to delineate the 42 pin DIP IC socket as there are two, a 2.54 pitch and a 1.78 pitch, the 1.78 being smaller. Lastly, there is a sentence that reads "don’t through the eprom away.", I believe that should read "don’t throw the eprom away.". Again, this is a wonderful guide, thank you very much for sharing as it has been a major boon as I try and navigate this subject. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.