Atari Flashback X Brazilian Variation

[RenatoDCD]

Hello everyone,

 

I have a question regarding the brazilian variation of Atari Flashback X, since its power output is not via a USB cable, not allowing to use the OTG cable method.

 

 

How can I upgrade this version easily, is there any SD support for this variation in its board?

 

Thanks in advance

[Slikatel]

I heard there is no way to hack these units. I don't think it is possible to update the firmware on these units.

 

The only idea I have is to solder a USB connection to the PCB board and use some kind of rockchip tool to push an update onto the unit.

 

I do have one question, what firmware version number does your About Screen show? Later U.S. models with the reset hole on the bottom came with OTG support out of the box.

[RenatoDCD]

On 4/25/2022 at 10:38 PM, Slikatel said:

I heard there is no way to hack these units. I don't think it is possible to update the firmware on these units.

 

The only idea I have is to solder a USB connection to the PCB board and use some kind of rockchip tool to push an update onto the unit.

 

I do have one question, what firmware version number does your About Screen show? Later U.S. models with the reset hole on the bottom came with OTG support out of the box.

Found out, it’s AR3060B_v0.0.2

[Slikatel]

yeah, I've never seen the PCB board so I have no idea if you can solder a USB port on that sucker or not.

 

Maybe if you can dump your firmware and hack it and push it back on, No clue.

Maybe rkflashtool would work?

[LucasIshida]

On 4/25/2022 at 5:58 PM, RenatoDCD said:

Hello everyone,

 

I have a question regarding the brazilian variation of Atari Flashback X, since its power output is not via a USB cable, not allowing to use the OTG cable method.

 

 

How can I upgrade this version easily, is there any SD support for this variation in its board?

 

Thanks in advance

Tectoy put a sticker over the micro usb port... you can just remove it

 

if you disassemble it, you will see that the micro usb is still there, but with a workaround adapted to use in the 127v plug... if you prefer, you can remove this wire (and the sticker on the micro usb) and feed it with a power supply. cell phone power.

 

the good side of this brazilian version is that it can feed the energy and use the usb without needing the OTG in Y.

 

The bad side is that by converting 127v to 5v it heats up considerably.

[RenatoDCD]

On 5/1/2022 at 2:34 AM, LucasIshida said:

Tectoy put a sticker over the micro usb port... you can just remove it

 

if you disassemble it, you will see that the micro usb is still there, but with a workaround adapted to use in the 127v plug... if you prefer, you can remove this wire (and the sticker on the micro usb) and feed it with a power supply. cell phone power.

 

the good side of this brazilian version is that it can feed the energy and use the usb without needing the OTG in Y.

 

The bad side is that by converting 127v to 5v it heats up considerably.

Many many many THANKS!

 

I just removed the sticker and for a question to end this (at least up to the next question lol), no need for any other mod than just placing the OTG in the microUSB port, right? (I won’t mess in the electrical side since I’m stupid in this matter).

[LucasIshida]

On 5/4/2022 at 7:28 AM, RenatoDCD said:

Many many many THANKS!

 

I just removed the sticker and for a question to end this (at least up to the next question lol), no need for any other mod than just placing the OTG in the microUSB port, right? (I won’t mess in the electrical side since I’m stupid in this matter).

no hardware modification is needed, just insert the otg and follow with "unlock" with custom firmware.
 

on my part, "as a curious person", I noticed that this adaptation made by tectoy leaves the two data pins unused, I'm thinking of a way to put the usb stick on the inside using the data pins, leaving the micro usb port on the outside free.

[rocketfan]

I'm glad to see the USB port was brought out on those after all.  Now I wish those Tectoy units could be imported into the US!

[Rodrigo Gouveia]

Em 05/05/2022 em 12:34, LucasIshida disse:

nenhuma modificação de hardware é necessária, basta inserir o otg e seguir com "desbloquear" com firmware personalizado.
 

da minha parte, "como curioso", notei que essa adaptação feita pela tectoy deixa os dois pinos de dados sem uso, estou pensando em uma forma de colocar o pendrive por dentro usando os pinos de dados, deixando o micro usb porta do lado de for livre.

Lucas, qual firmware personalizado você colocou, pode postar? Roda liso sem trabalhar?