shadow460 Posted September 9, 2009 Share Posted September 9, 2009 I have several of these controllers, most are for the N64 but one is for the PS1. They look like a very long Atari paddle controller with a trigger underneath, and the PS1 controller has a little negCon thrown in as well. The controllers are programmable. the N64 one is pretty well marked with what does what, but the PS1 one isn't. I think that A on the negCon is supposed to correspond with the square, but I do not know. I believe that someone has changed the configuration of my PS1 unit and I don't know how to reset it. Further, I know I personally have changed the configuration of one of my N64 units, but I've lost the instructions to know how to change it back. Vintage Stock has the N64 unit in the box from time to time, but I don't know if they have instructions. I imagine programming is similar to the PS1 unit. Anyone know how to program these things? All I get out of it is a red light and some beeps. Wait a sec, II corresponds to square on the negCon, and A must be the circle. I may have it... but I still could use those instructions. I'm trying to run Felony 11-79 with the Ultra Racer. I ran a test race so far, and it works well. Quote Link to comment Share on other sites More sharing options...
Classic Pac Posted September 9, 2009 Share Posted September 9, 2009 You could actually try here http://www.replacementdocs.com/news.php Quote Link to comment Share on other sites More sharing options...
shadow460 Posted September 10, 2009 Author Share Posted September 10, 2009 Didn't find it. I may just try Vintage Stock this weekend and see if one of theirs has docs. It'll be for the N64, but it should be close enough that I can figure everything else out. Maybe I'll get lucky and they will have a PS1 unit complete in the box. Quote Link to comment Share on other sites More sharing options...
james42519 Posted October 4, 2009 Share Posted October 4, 2009 I have several of these controllers, most are for the N64 but one is for the PS1. They look like a very long Atari paddle controller with a trigger underneath, and the PS1 controller has a little negCon thrown in as well. The controllers are programmable. the N64 one is pretty well marked with what does what, but the PS1 one isn't. I think that A on the negCon is supposed to correspond with the square, but I do not know. I believe that someone has changed the configuration of my PS1 unit and I don't know how to reset it. Further, I know I personally have changed the configuration of one of my N64 units, but I've lost the instructions to know how to change it back. Vintage Stock has the N64 unit in the box from time to time, but I don't know if they have instructions. I imagine programming is similar to the PS1 unit. Anyone know how to program these things? All I get out of it is a red light and some beeps. Wait a sec, II corresponds to square on the negCon, and A must be the circle. I may have it... but I still could use those instructions. I'm trying to run Felony 11-79 with the Ultra Racer. I ran a test race so far, and it works well. found instructions here. not sure where this person got them from though. http://www.digitpress.com/forum/showthread.php?t=66858 "Here's the instructions on how to relocate buttons: 1. To assign one button (i.e. "R") to perform another buttom function (i.e. "Z"): Press and hold the SET button for about 1 second to enter the "FUNCTION SETUP MODE", the FUNCTION SETUP LED will illuminate and two beeps will be heard. 2. Press the button (i.e. "R") you would like to reassign one time, the FUNCTION SETUP LED will blink once and a single beep will be heard. 3. Press the new, desired function (i.e. "Z") one tim, the NORMAL LED indicator will illuminate instead of the FUNCTION SETUP LED. Two beeps will be heard. The setting process is now complete. The UltraRacer 64 will only return to its default setting when the buttons "A", "L", and "R" are pressed at the same time BEFORE you turn on the console's power. After about two seconds, the UltraRacer 64 will generate three beeps to acknowledge reset button configuration is set. To reset a particular button, first press the SET button, then press the relocated button twice and then press the SET button once more until the LED light goes off. THe button's original function is used as a default button for further relocation." Quote Link to comment Share on other sites More sharing options...
+remowilliams Posted October 4, 2009 Share Posted October 4, 2009 Instructions for the UltraRacer PS UltraRacer.PS2.pdf Quote Link to comment Share on other sites More sharing options...
Like us on Facebook
Follow us on Twitter
AtariAge on Instagram
Watch us on YouTube
Chat on Discord
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.