vectrex Posted November 9, 2014 Share Posted November 9, 2014 I ended up buying from the UK btw so I am all set for now. Quote Link to comment Share on other sites More sharing options...
unebonnevie Posted June 24, 2015 Share Posted June 24, 2015 Sorry for an off beat question: But does anyone know of the pitch for the Vectrex 36-pin (18 pins on each side) edge connector. I am looking to buy an edge connector from eBay to replace my Vector's edge connector, but wanted to make sure I get the right pitch. Thanks! Quote Link to comment Share on other sites More sharing options...
silverfox0786 Posted August 14, 2015 Share Posted August 14, 2015 is this going ahead? Quote Link to comment Share on other sites More sharing options...
+5-11under Posted August 14, 2015 Author Share Posted August 14, 2015 is this going ahead? Not at this point (unless I can be convinced otherwise ). Quote Link to comment Share on other sites More sharing options...
silverfox0786 Posted August 19, 2015 Share Posted August 19, 2015 Not at this point (unless I can be convinced otherwise ). what could I do to convince you as I would really like to try and convince you Quote Link to comment Share on other sites More sharing options...
+5-11under Posted August 19, 2015 Author Share Posted August 19, 2015 what could I do to convince you as I would really like to try and convince you Buy 1000+ shells. Quote Link to comment Share on other sites More sharing options...
50TBRD Posted August 20, 2015 Share Posted August 20, 2015 Unfortunately, Collectorvision is no longer getting into Vectrex games, so it would be very difficult to find someone who wanted a significant number of carts. George Pelonis has had to find an alternate method of housing his PCBs for Warrior and future games. I still think that doing a translucent run would be your best bet of getting a new mold made. Quote Link to comment Share on other sites More sharing options...
+5-11under Posted August 20, 2015 Author Share Posted August 20, 2015 Unfortunately, Collectorvision is no longer getting into Vectrex games, so it would be very difficult to find someone who wanted a significant number of carts. George Pelonis has had to find an alternate method of housing his PCBs for Warrior and future games. I still think that doing a translucent run would be your best bet of getting a new mold made. Can't he buy shells from Sean Kelly? Quote Link to comment Share on other sites More sharing options...
Mayhem Posted August 20, 2015 Share Posted August 20, 2015 Unfortunately, Collectorvision is no longer getting into Vectrex games, so it would be very difficult to find someone who wanted a significant number of carts. Well, that explains why Brecher is coming out through Luchs Soft directly in the near future then. Sascha never mentioned anything about Collectorvision when I spoke to him recently. Quote Link to comment Share on other sites More sharing options...
50TBRD Posted August 20, 2015 Share Posted August 20, 2015 CollectorVision has decided to focus on Super Nintendo as its new endeavor which coincides perfectly with Sasha self-publishing his games. I don't believe George can get them from Sean anymore. People receiving Warriors currently are stating that the PCBs come in raw molded shells or a 3D printed type. They have a few rough edges and pieces have been falling off. Quote Link to comment Share on other sites More sharing options...
+5-11under Posted August 20, 2015 Author Share Posted August 20, 2015 Good to know... . Quote Link to comment Share on other sites More sharing options...
ozyr Posted August 28, 2015 Share Posted August 28, 2015 Surprised he can't get these from Sean. I got another batch earlier this year from Sean (April), but I got the impression that Sean was running a bit low on the shells. Don't like saying it too loudly here, but I think I bought the majority of his last batch, as Packrat has been selling so many Vectrex games since last Fall. I ran out of the first batch I bought in just 6 months, and it was supposed to last 3 years! I'd still be interested in these, especially translucent shells. Depending on price, I would possibly be interested in a batch (but not 1,000 at this point in time — maybe in the next 6 months or so though). 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.