Jump to content
IGNORED

SDrive-MAX ATX support


Farb

Recommended Posts

10 hours ago, JagChris said:

What is this? An update for the SDMax?

Yes, the last one is v1.3 where several things were corrected "read github".
Now I published version 1.4 beta compiled "for testers and developers".

testing what I shared ๐Ÿ˜

sdrive.thumb.jpg.a0cf1622e2599b4953180e0d4a620baa.jpg

Link to comment
Share on other sites

1 hour ago, JagChris said:

How do I implement it?

ย 

7 minutes ago, Ricky Spanish said:

Seems my Xloader doesn't even show UNO as an option. How are you guys getting the Sdrive to show on it ?

I'm still a v1.2 ๐Ÿ™„

here it is explained ๐Ÿ˜‰

  • Thanks 1
Link to comment
Share on other sites

47 minutes ago, Ricky Spanish said:

Now it's showing can't open port.. like wtf ?

if you are a novice user or if you bought this device, the first thing to do is to detect which chip the touch screen is using. when the correct firmware is not used, the screen remains idle, but don't worry, you can re-record again.๐Ÿ˜‰

ย 

10 minutes ago, JagChris said:

Ill check this out this weekend. I'm assuming it includes list of fixes/improvements. I'm guessing it addresses the screensaver issues?

about your question that happened in very old versions of firmware ๐Ÿ˜‰

Link to comment
Share on other sites

54 minutes ago, JagChris said:

Ill wait to see how this gets resolved before I attempt this.

Resolved. There are seven atmega328 folders, the correct one for me was:

atmega328-hx8347i

However v1.3 did not resolve the issue with spartados_3.2G.atr having to be booted from D0 with FastSIO $10 39000.

Any setting faster than 39000 it will not boot even from D0.

Edited by Ricky Spanish
clarity
  • Thanks 1
Link to comment
Share on other sites

24 minutes ago, Ricky Spanish said:

However it did not resolve the issue with spartados_3.2G.atr having to be booted from D0 with FastSIO $10 39000.

Any setting faster than 39000 it will not boot even from D0.

first what version did you install?
secondly if you want to use FastSIO I use it from SDrive-ng? ๐Ÿ˜…

Link to comment
Share on other sites

7 minutes ago, ascrnet said:

first what version did you install?
secondly if you want to use FastSIO I use it from SDrive-ng? ๐Ÿ˜…

show SIO error 3 in various places when in debug mode.

Version: sdrive-max-v13 says by KBr V1.3

Just want spartados to boot from D1. Right now it only boots from D0 by pressing [INVERT]

ย 

Edited by Ricky Spanish
added info
Link to comment
Share on other sites

8 minutes ago, Ricky Spanish said:

Just want spartados to boot from D1. Right now it only boots from D0 by pressing [INVERT]

it is strange since the D0 is only for SDrive-ng "the black menu" and this can increase the speed of the sio when loading from it. from the touch screen it is only to drive the D1 to D4 units and activates/deactivates the D0.๐Ÿ˜…

Link to comment
Share on other sites

5 hours ago, Ricky Spanish said:

The vid:

it's ok that it happens, now I explain:

ย 

what happens is that sdrive-max by default leaves the sio at $06 and this is incompatible with the spartdos boot must have a speed higher than $07 or use the default speed which is $28 with these conditions load perfect.

ย 

I tried with other devices like the avgcart and it behaved the same, the difference is that when you adjust the speed of the sio it is saved so that when you turn it on again it is already configured.

ย 

in short, it needs to save the speed of the sio.๐Ÿ˜…

  • Like 1
Link to comment
Share on other sites

1 minute ago, ascrnet said:

in short, it needs to save the speed of the sio.๐Ÿ˜…

I have no problems getting it to boot.

ย 

In short here's an assignment for you:

Save however you think it works.

Turn off the computer

Unplug the Sdrive

Plug-in the Sdrive

Try to load spartados 3.2

Report back

ย 

ย 

ย 

ย 

ย 

ย 

Link to comment
Share on other sites

1 hour ago, Ricky Spanish said:

I have no problems getting it to boot.

ย 

In short here's an assignment for you:

Save however you think it works.

Turn off the computer

Unplug the Sdrive

Plug-in the Sdrive

Try to load spartados 3.2

Report back

i did that already, when i turn everything off always the sdrive-max is on speed $06. as i explained before that's why it doesn't work until you change the speed in the drive-ng.

ย 

ย 

Edited by ascrnet
edit
  • Like 1
Link to comment
Share on other sites

On 5/12/2023 at 3:10 PM, _The Doctor__ said:

SD Max Screen saver issues and long file name issues have been covered to death. The horse gets drug around and the glue never seems to stick, so we cover it some more. I suspect it'll get fixed when enough people make noise about it. OR somebody with the skill up and does it.

It looks like at least the screensaver issue may be solvable with an update. We shall see.

Link to comment
Share on other sites

ย 

1 hour ago, ascrnet said:

as i explained before that's why it doesn't work until you change the speed in the drive-ng.

ย 

2 hours ago, ascrnet said:

or use the default speed which is $28 with these conditions load perfect.

I have it saved at fastSIO $28. BootLoader $0700-07F7. I'm telling you, on my 1200XL it will NOT load sparta if I unplug the Sdrive then plug it in.

FastSIO $28. BootLoader $0700-07F7 is still saved in the config.ย 

20230514_000407.thumb.jpg.2b2a28185cb77a08766ebe15508f5dd2.jpg

Edited by Ricky Spanish
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
  • Recently Browsing   0 members

    • No registered users viewing this page.
ร—
ร—
  • Create New...